Installation method of lithium battery solar street lamp

by:Road Smart     2020-02-21
Solar energy is an inexhaustible, clean, pollution-free and renewable green and environmentally friendly energy. The use of solar power, incomparable cleanliness, high safety, energy relative universality and adequacy, long life and maintenance free and other conventional energy does not have the advantages. Solar cell components generally choose monocrystalline silicon or polycrystalline silicon solar cell components. LED Lamp caps generally use high-power LED light source, and the controller is generally placed in the lamp pole, with light control, time control, overcharge and overdischarge protection and reverse connection protection, the more advanced controller has the function of adjusting lighting time in four seasons, half power function, intelligent charging and discharging function, etc. The most efficient thing is to add a lithium battery to the solar energy. If you add a battery, your solar panel will be useless. Ordinary batteries cannot be charged. When the battery is used up, there will be no sun, you can't use it. If it is a lithium battery, it can be used for a long time. Although it is a little expensive at the beginning, it is practical, and a small lithium battery will not exceed 10 pieces. So it is better to have a lithium battery. Today's mass consumers rely heavily on energy technology and its development. At present, the three key technologies related to energy are intelligent electronic products, electric vehicles and smart grids. Intelligent Electronic products rely on batteries with limited capacity and need to frequently charge electronic devices using wired connections. Solar energy or photovoltaic provides possible convenience for battery charging, because the energy density of solar energy can reach 100mWcm-2 in outdoor sunlight. At present, another thriving market is the electric vehicle industry. Although electric vehicles do not produce carbon emissions, most of the electricity used by automobiles comes from fossil fuel-driven power grids. The traditional method of using solar cells to charge the battery is to design two systems independently, and the solar cells and energy storage batteries involved are connected by wires as two independent units; Such systems are often more expensive and require more space. In addition, external wires will lead to power loss. Organically combining production capacity and energy storage into one unit to realize integrated design will effectively solve the energy density problem of solar cells and batteries. This design has the characteristic of miniaturization and increases the practicability of photovoltaic system. Despite many advantages, there are still great challenges in efficiency, capacity and stability. At present, the research in this field is still in the primary stage, and the focus of the research is mainly on the design of materials and devices. The installation method of lithium battery solar street lamp is as follows: 1. Embedded parts. Dig up the 6-meter street lamp in the pre-buried pit as an example: about 60*60 in size, 70 in depth, leave the screw rod position, stick it with adhesive tape, and bury it for pouring. Two: Wiring: 1: lithium battery and LED lamp wiring method. 2: load output: positive and negative (Red line represents positive pole, black line represents negative pole); The positive pole is connected to the positive pole of the LED lamp, and the negative pole is connected to the negative pole of the LED lamp. 3. Wiring method of lithium battery and solar panel, solar energy input: positive and negative electrodes; The positive pole is connected with the positive pole of the solar panel, and the negative pole is connected with the negative pole of the solar panel. Three: connect the connecting line and check the charging indicator light (Green light G)Whether it is normally bright; If it is on normally, pull out the solar energy input after 10 seconds, and the load output LED light is on normally; Re-connect the solar energy input, and the load output LED lamp will go out after 10 seconds. Four: precautions :(1) The lithium-controlled integrated battery is installed to the corresponding position of the four screw holes reserved for the solar panel bracket. (2) The solar panel is installed in the solar panel bracket with four holes reserved and the corresponding reserved positions are fixed by screws. (3) The installation bracket of solar panel and lithium-controlled integrated storage battery is completed and fixed on the top of street lamp pole. (4) The wiring on the back of the solar panel is designed as a reverse button. The screwdriver can be used to gently pry it open. The solar panel is wired to correspond to the positive and negative wires separated from the black cap of the lithium-controlled integrated battery. The wiring should be wrapped with electrical adhesive tape.
In the office, various are considered essential since they are used to achieve particular tasks in the office. Among these , solar power systems prices, solar powered street lamps price, and solar panel and led lights are widely used.
Helping the needy high power outdoor solar lights industries with quality products had been our main goal and we have succeeded in providing simple and effective solutions which has a huge scope to be implemented in the near future. Go to Road Smart Solar Led Light to know more about us.
Socreat Electronics Technology Limited incorporates average length of the workweek, average growth in number of small businesses, startup per capita, average of growth of business revenues, five-year business survival rate, industry variety, entrepreneurship index and how digital a state is.
Custom message
Chat Online 编辑模式下无法使用
Chat Online inputting...
Hi, message received, will get in touch with you soon